Techno Expert Level 2

“Techno Expert Level 2”

108 hours Training & Learning on “Embedded System, Robotics & Automation”
For: - 1st, 2nd, 3rd, 4th year B. E. / B. Tech. (ECE, EE, EEE, EIC, CS, IT, ME, Automobile), M. E./ M. Tech., MCA, BCA, B. Sc. – I. T., M. Sc.,B. Arch., M. Tech. & Professionals.

Topics Cover: -

The training is going to cover & give practical hands on following topics:

  • Electronics components overview
  • Circuit Designing & Simulation
  • EMI & EMC Considerations
  • Schematic Designing
  • PCB Layout Design
  • Placement & Routing
  • Component Packaging
  • Footprint Designing
  • Material Selection
  • PCB Fabrication
  • PCB Track Etching
  • PCB Fabrication @ HOME
  • Chemical Solutions
  • Masking & Printing
  • Negative Preparation
  • Bulk Production
  • Embedded System
  • Difference between Microprocessor and Micro-controllerv
  • Howard and Von-Neumann Architecture
  • CISC and RISC
  • Micro-controller & Applications
  • Memory Organization
  • Internal Architecture of RAM
  • 8051 Programming Architecture
  • PIN Description of 8051/8031
  • Input/output Pin Architecture of 8051
  • Basics of C language
  • Embedded C Programming
  • Programming Simulation
  • Input and Output Interface
  • LED Interfacing
  • DIP Switch Interfacing
  • Sensors & Sensor Interfacing
  • Analog Sensor
  • Digital Sensor
  • Temperature Sensor
  • Switch Interfacing
  • 7-Segment Interface
  • Pattern Generation on 7-segment
  • Pattern generation on alphanumeric segment
  • Timer
  • Interrupt
  • LED Dot-matrix Display Interfacing
  • Wireless Interfacing Using RF Module
  • Actuators designing
  • DC Motor Interfacing
  • Stepper Motor Interfacing
  • Relay Driver & Interfacing
  • DTMF Concept and Interfacing
  • LCD Interfacing: 8 Bit & 4 Bit.
  • Linear & Matrix Keyboard Interface
  • LCD and keyboard interfacing with micro controller
  • Bi-lateral Serial Communication
  • Bi-lateral Parallel Communication
  • Analog-to-Digital Conversation
  • Serial Protocols
  • I2C
  • UART
  • RTC Interfacing
  • EEPROM interfacing
  • Simulators
  • Debugging
  • Introduction to AVR Family Micro-controller.
  • ‘Kaizen Tech’ Competition among participants.
  • Result & Revision.
  • Conclusion & Videos.
  • Writing research paper.
  • IPR.
  • Introduction to Advance Controllers.

Projects Cover: -
During this training each and every student is going to design own following projects with their own hands using their own “Advance Personal Robotic Lab”:
1. Digital Clock
2. Green House Controller
3. Development Board
4. Temperature Regulated System
5. Linear & Matrix Keypad Interfacing
6. Password Protected Entry System
7. Dynamic Moving LCD Display
8. Electronic Voting Machine
9. Metro Train Prototype
10. 4-Bit & 8-Bit LCD Control
11. Real Time Clock
12. Wireless Controlled Robotic Arm.
13. Bi directional visitor counter
14. And Many More.
For Students: -

Advance Personal Robotic Lab will be given to Every Students i.e. 1 Personal Robotic Kit worth Rs. 5,000/- per student during training period that student will take away with them.

Advance Personal Robotic Lab consisting of:-

    • 8051 Development Board.
    • Multimeter
    • LEDs: 3mm, 5mm; W/W, W/R, W/G, W/O, W/B, W/IR, R/R, G/G.
    • Micro-Controller: AT89S52.
    • RF Module: 433 MHz.
    • Resisters: Fixed, Variable Resister & Resister Array
    • Capacitors: Ceramic, Polyester & Electrolytic.
    • Diodes: Normal Diode, Power Diode.
    • Bread-Board, Vero Board & Copper Clad PCB.
    • Displays: Alpha – Numeric & Common Anode/Cathode, LED Dot-Matrix, LCD.
    • Relays
    • Switches: Reset Switch, Push-to-On-Push-to-Off, DPDT, DIP.
    • Transistors: NPN, PNP, Power Transistor.
    • Crystal Oscillator: 3.57 MHz, 11.0592 MHz, 36KHz.
    • Sensors: Analog, Digital, Light, Heat, Temperature.
    • ICs: 7805, LM324, NE555, MAX232.
    • IC Base: 8 Pin, 14 Pin, 16 Pin, 18 Pin, 20 Pin, 28 Pin, 40 Pin.
    • Burg Strip: Male, Female.
    • Encoder: HT12E.
    • Decoder: DTMF Decoder MT8870, HT12D.
    • ADC: 0808/0809.
    • RTC: DS1307.
    • External ROM: 24C04.
    • Relay Driver: ULN2803.
    • Motor Driver: L293D.
    • Keypad: Linear, & Matrix.
    • DC Gear Motor: 100/150 RPM.
    • Stepper Motor.
    • Wheels.
    • Chassis: Plastic & Metal.
    • Soldering Iron Set: Soldering Iron, Iron Stand, Desoldering Pump, Flux, Foam.
    • Isolators.
    • Connectors: 2 Pin, 3 Pin Relement Connectors, DB-9 Connector.
    • Wire Stripper.
    • Nipper.
    • Wires: Single & Multi Line Wire, Single Core & Multi Core Wire.
    • Nose Pliers.
    • Screw Driver.
    • Twisser.
    • Hack saw.
    • Aluminum Rod.
    • Battery: Non-Rechargeable 9V & Chargeable 6V.
    • Battery Charger.
    • Micro-controller Burner.
    • Insulation Tape.
    • Nutt-Bolt
    • Glue
    • Carry Boxes
    • Every participant will take away their Robotic Models.
    • Full Study Material containing:
    • 8051 Micro-controller Book: Mazidi – Mazidi – McKinlay [Optional on extra cost].
    • Course Manual for Techno Expert Level 2: By Kaizen Robeonics Research Pvt. Ltd.
    • Data Sheets
    • Report Matter
    • Course Layout
    • Project Coverage

Pre-Requisites from Students: –

    • Candidate should require good command on circuit designing, bread-boarding, soldering, circuit de-bugging.
    • Candidate should require sound basic understanding of 8051 Micro-Controller.
    • Candidate should require good understanding of C Language.